JET START 510A AND 510A5

CONTACT US TO REVIEW OUR JET START 510A AND 510A5

If you missed FABTECH 2021, you missed the chance to see the Jet Start 510A and 510A5 Mid Rail Abrasive Waterjet systems in action!

510A  510A5 Waterjet System - Jet Edge

 

JET EDGE JET START 510A MID RAIL ABRASIVE WATERJET SYSTEM

The Jet Start 510A takes the no-nonsense workhorse 3-axis, 5' x 10' motion system and pairs it with Jet Edge’s HERO 50 intensifier pump that is loaded with features including Jet Smart controls. The result is an Abrasive Waterjet system capable of cutting complex parts from virtually any material with ultra-high precision.

Click here to download the spec sheet!

 

JET EDGE JET START 510A5 MID RAIL ABRASIVE WATERJET SYSTEM

The Jet Start 510A5, 5-axis motion system launches you into complex, contoured cutting right from the start. Combining Jet Edge’s premium 5' x 10' mid rail motion system with Jet Edge’s HERO 50 intensifier pump featuring Jet Smart controls, dramatically expands your production capabilities.

Waterjet complex, precision shapes in tough materials like stainless steel, Inconel and titanium with no Heat Affected Zone like you see with laser or plasma cutting.

Click here to download the spec sheet!

JET START MID RAIL SYSTEMS AT A GLANCE: 

➤ Isolated motion system for accuracy

➤ Adjustable pre-loaded anti-backlash recirculating ball screws

➤ Linear bearings, hardened precision ground ways

➤ Protected critical bearing components with labyrinth seals and positive air pressure

➤ Direct-couple, AC brushless servo motors with absolute encoders

➤ Dual synchronized Y-axis drive system

HERO 50 WITH JET SMART CONTROLS AT A GLANCE: 

➤ 60,000 psi/4,100 bar pressure rating

➤ 50 hp/37 kw TEFC NEMA premium efficiency motor

➤ Jet Smart interactive controls w/touch screen

➤ Remote start with Wye-Delta motor starter

➤ Single, 1 quart/0.9 liter attenuator

➤ Dual plunger intensifier with tie rod design

➤ UHP flow rate 1.1 gpm/4.1 lpm

➤ 24 Hour Technical service

➤ Free lifetime factory training

THE TALE OF THE TAPE!

 

Jet Start 510A 3 Axis Motion System w/HERO 50 UHP Pump

Jet Start 510A5 5 Axis Motion System w/HERO 50 UHP Pump

Jet Start 510 Motion Systems

Mid Rail 5’ x 10’ work surface

Mid Rail 5’ x 10’ work surface

Cutting Head

3 Axis AbrasiveJet Cutting Head

5 Axis AbrasiveJet Cutting Head

Mid Rail Z Package

Motorized, 12” Z Axis travel

Servoed, 12” Z Axis travel

Aquavision Di Controller with Windows 10

Standard

Standard

IGEMS CAM Programming Software

Standard

Standard

Full featured Handheld Pendant

Standard

Standard

Abrasive Catch Tank with Slat Kit

Standard

Standard

800lb Solid Phase Bulk Hopper

Standard

Standard

Basic Installation and Training

Standard

Standard

 

 

 

HERO 50 UHP Intensifier Pump

With Jet Smart Controls

With Jet Smart Controls

Control Panel

Interactive Touch Screen

Interactive Touch Screen

Pressure Rating

60,000 psi/4,100 bar

60,000 psi/4,100 bar

Electric Motor

50 hp/37 kw

50 hp/37 kw

Intensifier

Single Tie Rod Design

Single Tie Rod Design

Remote Pump Start

Standard

Standard

Wye-Delta Motor Starter

Standard

Standard

Dual pressure set points

Standard

Standard

Manual pressure control w/Soft Start accumulator

Standard

Standard

Incoming Water Control Kit

Standard

Standard

 

Jet Start 510A and Jet Start 510A5 Abrasive Waterjet Systems w/HERO 50 UHP Pump

Contact us for FabTech Show Specials!