JET START 510A AND 510A5

CONTACT US TO REVIEW OUR JET START 510A AND 510A5

If you missed FABTECH 2021, you missed the chance to see the Jet Start 510A and 510A5 Mid Rail Abrasive Waterjet systems in action!

JET EDGE JET START 510A MID RAIL ABRASIVE WATERJET SYSTEM

The Jet Start 510A takes the no-nonsense workhorse 3-axis, 5' x 10' motion system and pairs it with Jet Edge’s HERO 50 intensifier pump that is loaded with features including Jet Smart controls. The result is an Abrasive Waterjet system capable of cutting complex parts from virtually any material with ultra-high precision.

Click here to download the spec sheet!

JET EDGE JET START 510A5 MID RAIL ABRASIVE WATERJET SYSTEM

The Jet Start 510A5, 5-axis motion system launches you into complex, contoured cutting right from the start. Combining Jet Edge’s premium 5' x 10' mid rail motion system with Jet Edge’s HERO 50 intensifier pump featuring Jet Smart controls, dramatically expands your production capabilities.

Waterjet complex, precision shapes in tough materials like stainless steel, Inconel and titanium with no Heat Affected Zone like you see with laser or plasma cutting.

Click here to download the spec sheet!

JET START MID RAIL SYSTEMS AT A GLANCE:

➤ Isolated motion system for accuracy

➤ Adjustable pre-loaded anti-backlash recirculating ball screws

➤ Linear bearings, hardened precision ground ways

➤ Protected critical bearing components with labyrinth seals and positive air pressure

➤ Direct-couple, AC brushless servo motors with absolute encoders

➤ Dual synchronized Y-axis drive system

HERO 50 WITH JET SMART CONTROLS AT A GLANCE:

➤ 60,000 psi/4,100 bar pressure rating

➤ 50 hp/37 kw TEFC NEMA premium efficiency motor

➤ Jet Smart interactive controls w/touch screen

➤ Remote start with Wye-Delta motor starter

➤ Single, 1 quart/0.9 liter attenuator

➤ Dual plunger intensifier with tie rod design

➤ UHP flow rate 1.1 gpm/4.1 lpm

➤ 24 Hour Technical service

➤ Free lifetime factory training

THE TALE OF THE TAPE!

	Jet Start 510A 3 Axis Motion System w/HERO 50 UHP Pump	Jet Start 510A5 5 Axis Motion System w/HERO 50 UHP Pump
Jet Start 510 Motion Systems	Mid Rail 5’ x 10’ work surface	Mid Rail 5’ x 10’ work surface
Cutting Head	3 Axis AbrasiveJet Cutting Head	5 Axis AbrasiveJet Cutting Head
Mid Rail Z Package	Motorized, 12” Z Axis travel	Servoed, 12” Z Axis travel
Aquavision Di Controller with Windows 10	Standard	Standard
IGEMS CAM Programming Software	Standard	Standard
Full featured Handheld Pendant	Standard	Standard
Abrasive Catch Tank with Slat Kit	Standard	Standard
800lb Solid Phase Bulk Hopper	Standard	Standard
Basic Installation and Training	Standard	Standard

HERO 50 UHP Intensifier Pump	With Jet Smart Controls	With Jet Smart Controls
Control Panel	Interactive Touch Screen	Interactive Touch Screen
Pressure Rating	60,000 psi/4,100 bar	60,000 psi/4,100 bar
Electric Motor	50 hp/37 kw	50 hp/37 kw
Intensifier	Single Tie Rod Design	Single Tie Rod Design
Remote Pump Start	Standard	Standard
Wye-Delta Motor Starter	Standard	Standard
Dual pressure set points	Standard	Standard
Manual pressure control w/Soft Start accumulator	Standard	Standard
Incoming Water Control Kit	Standard	Standard

Jet Start 510A and Jet Start 510A5 Abrasive Waterjet Systems w/HERO 50 UHP Pump

Contact us for FabTech Show Specials!